Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.
Power Management for Glyph S3 Motor Driver
The design has a USB-C input, a single-cell battery connector and charger, a 3.3 V logic regulator, and an integrated motor driver. The motor driver uses the board’s +BATT rail for VM.
Battery + USB power
USB-C (J4): USB power, native USB programming, and serial debugging. The USB input passes through the F1 polyfuse.
Battery connector (J6): Pin 1 is GND; pin 2 is Bat_PWR (battery positive).
Battery charger: The MCP73831-2-OT is configured for a single-cell LiPo/Li-ion battery with a 4.2 V charge voltage. Charge current is set by the charger circuit on the board.
VBUS pin: J1 pin 3 exposes the USB 5 V rail.
The schematic routes USB VBUS through the F1 polyfuse and SS34 diode D3 to the +BATT system rail. The MCP73831 takes VBUS at its input and connects its battery output to Bat_PWR at J6 pin 2. The SI2301 MOSFET is also part of the board’s battery/power-path circuit. +BATT feeds both the AP2112K-3.3 regulator and the TB6612FNG motor-supply pins.Use a single-cell 3.7 V nominal LiPo/Li-ion battery, with 4.2 V maximum charge voltage, at J6. Connect it with the correct polarity.
Do not connect alkaline or NiMH batteries to J6, and do not apply more than 4.2 V to the single-cell battery input. Reversed polarity can damage the board.
Regulated logic power
The AP2112K-3.3 regulator supplies the board’s 3.3 V logic rail from +BATT. The regulator datasheet specifies a 600 mA continuous load rating; the available board-level current also depends on thermal conditions and other loads. The 3.3 V rail is exposed on J2 pins 2 and 3, pad J3, and Glink connector J5 pin 2.Do not power motors from a GPIO pin or the 3.3 V rail.
Motor power
The TB6612FNG logic VCC pin is connected to the 3.3 V rail. Its motor VM pins connect to the board’s +BATT rail, which is also exposed at J1 pin 1. The schematic does not show a separate motor-supply connector; the motor driver’s supply follows the board’s USB/battery power path.The TB6612FNG IC has a 2.5–13.5 V motor-supply operating range, with 1.2 A average output per channel. Its 3.2 A rating is for a single pulse and is not a continuous rating. These are IC limits; they do not mean the board’s battery input can accept 13.5 V. Keep the board supply within its single-cell battery and system-rail limits, and check each motor’s stall current. See Toshiba’s TB6612FNG datasheet.The controller, driver, and motor supply share ground. J7 carries Motor A outputs (AO_2 on pin 1, AO_1 on pin 2); J8 carries Motor B outputs (BO_2 on pin 1, BO_1 on pin 2). See Pinouts.
Do not apply a separate high-voltage motor supply to +BATT, J6, or the motor output connectors. +BATT is shared with the board power path. Check motor stall current and polarity before use.
Measuring battery voltage
The board schematic labels GPIO1 as D1/BATT_MSR. This signal is available at J1 pin 10 for battery-voltage measurement. See the board-specific pinout before connecting other circuitry to it.
Driver standby
The TB6612FNG STBY input is connected to GPIO42. Drive STBY low to put the motor driver in standby; drive it high to enable the output channels. Standby disables the driver outputs, but it does not disconnect the board’s battery or USB power.For general ESP32-S3 sleep modes and USB/battery guidance, see Glyph S3 Power Management. See the AP2112 product datasheet and MCP73831 charger datasheet for IC details.
{"docsConfig":{"theme":"mint","$schema":"https://mintlify.com/docs.json","name":"PCB Cupid","colors":{"primary":"#0D9373"},"favicon":"https://mintcdn.com/pcbcupid-bae3761c/4dXNuJjZhqL5zqVd/images/favicon_PCBcupid.png?fit=max\u0026auto=format\u0026n=4dXNuJjZhqL5zqVd\u0026q=85\u0026s=697c4189e0a983e1722bddbedde79f61","appearance":{"strict":true},"background":{"decoration":"gradient"},"navbar":{"links":[{"href":"https://spell.pcbcupid.com","label":"Circuit Spell"},{"href":"https://shop.pcbcupid.com","label":"Shop"},{"href":"/","label":"Learn"},{"href":"https://events.pcbcupid.com","label":"Events"},{"href":"https://forum.pcbcupid.com","label":"Forum"},{"href":"https://pcbcupid.com/articles","label":"Articles"},{"href":"https://pcbcupid.com/tools","label":"Tools"}]},"seo":{"indexing":"all"},"fonts":{"family":"Space Grotesk","weight":400},"icons":{"library":"lucide"},"styling":{"eyebrows":"breadcrumbs","latex":true},"contextual":{"options":["copy","chatgpt","claude","cursor","vscode","mcp"],"display":"toc"},"thumbnails":{"appearance":"dark"},"navigation":{"pages":[]}},"deployment":{"deploymentMetadataValue":{"subdomain":"pcbcupid-bae3761c","hasAudioNarration":false,"actualSubdomain":"pcbcupid-bae3761c","customDomains":["learn.pcbcupid.com"],"gitSource":{"type":"github","owner":"pcbcupid","repo":"pcbcupid-docs","deployBranch":"main","contentDirectory":"","isPrivate":false,"mountPath":"","label":""},"feedback":{"thumbs":true,"edits":true,"issues":true},"entitlements":{"AI_CHAT":{"status":"DISABLED"}},"buildId":"6b0055c72d0cf2e9fca1a709","clientVersion":"0.0.4248","searchFilterCounts":[{"language":"default","tag":"Documentation","count":80},{"language":"default","tag":"Modules","count":70},{"language":"default","tag":"PCB Design","count":45},{"language":"default","tag":"Examples","count":32},{"language":"default","tag":"Glyph","count":28},{"language":"default","tag":"G-Mod","count":17},{"language":"default","tag":"KiCad","count":16},{"language":"default","tag":"Basic","count":15},{"language":"default","tag":"Welcome","count":9},{"language":"default","tag":"G-Sense","count":8}]},"assistantConfig":{"enableAskAiButton":false,"enableStarterQuestions":false,"enableContextualStarterQuestions":false,"enableAskAiSearchBar":true},"basePath":"","hasChatPermissions":false,"hasWebMcpPermissions":false,"toggles":[{"name":"kill-isr","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-rbac-roles","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-mintlify-slack","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-integrations-settings","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"rbac-expansion","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-pr-grouping","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-prefix","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"analytics-v7","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"user-flows-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"no-publish-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-onboarding","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving-live","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"stripTemperatureMiddleware","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"support-platform-pylon-zendesk","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"instant-rollback","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications-server","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-fable","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fixed-ai-action-pricing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"site-roles","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automation-resolve-merge-conflict","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"scoped-publishing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"mintql","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"page-level-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-version-history-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"billing-page-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"full-page-search","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workspace-projects","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"assistant-v5","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fork-pr-previews","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"revalidation-jwt","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-sso-scim","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"hobby-abuse-scan","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"dashboard-inbox","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-signup","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-dual-write","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-enabled","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"approve-review-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-metadata","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"sso-setup-deadline-banner","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-serve","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"live-agents","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"starter-pricing","enabled":true,"variant":{"name":"control","enabled":true,"payload":{"type":"string","value":"control"},"feature_enabled":true},"impressionData":false},{"name":"llms-txt-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"wildcard-email-auth","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false}],"googleFontsInlined":true},"customCss":[]}
{"page":{"pagePath":"documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management","slug":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management","pageMetadata":{"description":"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.","title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management"},"description":{"compiledSource":"\"use strict\";\nconst {jsx: _jsx} = arguments[0];\nconst {useMDXComponents: _provideComponents} = arguments[0];\nfunction _createMdxContent(props) {\n const _components = {\n p: \"p\",\n ..._provideComponents(),\n ...props.components\n };\n return _jsx(_components.p, {\n children: \"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\"\n });\n}\nfunction MDXContent(props = {}) {\n const {wrapper: MDXLayout} = {\n ..._provideComponents(),\n ...props.components\n };\n return MDXLayout ? _jsx(MDXLayout, {\n ...props,\n children: _jsx(_createMdxContent, {\n ...props\n })\n }) : _createMdxContent(props);\n}\nreturn {\n default: MDXContent\n};\n","frontmatter":{},"scope":{}},"pageType":"default","mdx":{"mdxSource":{"compiledSource":"\"use strict\";const{Fragment:_Fragment,jsx:_jsx,jsxs:_jsxs}=arguments[0];const{useMDXComponents:_provideComponents}=arguments[0];function _createMdxContent(props){const _components={a:`a`,li:`li`,p:`p`,strong:`strong`,ul:`ul`,..._provideComponents(),...props.components},{Danger,Heading,Warning}=_components;if(!Danger)_missingMdxReference(`Danger`,true);if(!Heading)_missingMdxReference(`Heading`,true);if(!Warning)_missingMdxReference(`Warning`,true);return _jsxs(_Fragment,{children:[_jsx(Heading,{level:`2`,id:`power-management-for-glyph-s3-motor-driver`,children:`Power Management for Glyph S3 Motor Driver`}),`\n`,_jsxs(_components.p,{children:[`The design has a USB-C input, a single-cell battery connector and charger, a 3.3 V logic regulator, and an integrated motor driver. The motor driver uses the board’s `,_jsx(_components.strong,{children:`+BATT`}),` rail for VM.`]}),`\n`,_jsx(Heading,{level:`3`,id:`battery-+-usb-power`,children:`Battery + USB power`}),`\n`,_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`USB-C (J4):`}),` USB power, native USB programming, and serial debugging. The USB input passes through the F1 polyfuse.`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Battery connector (J6):`}),` Pin 1 is GND; pin 2 is Bat_PWR (battery positive).`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Battery charger:`}),` The MCP73831-2-OT is configured for a single-cell LiPo/Li-ion battery with a 4.2 V charge voltage. Charge current is set by the charger circuit on the board.`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`VBUS pin:`}),` J1 pin 3 exposes the USB 5 V rail.`]}),`\n`]}),`\n`,_jsx(_components.p,{children:`The schematic routes USB VBUS through the F1 polyfuse and SS34 diode D3 to the +BATT system rail. The MCP73831 takes VBUS at its input and connects its battery output to Bat_PWR at J6 pin 2. The SI2301 MOSFET is also part of the board’s battery/power-path circuit. +BATT feeds both the AP2112K-3.3 regulator and the TB6612FNG motor-supply pins.`}),`\n`,_jsx(_components.p,{children:`Use a single-cell 3.7 V nominal LiPo/Li-ion battery, with 4.2 V maximum charge voltage, at J6. Connect it with the correct polarity.`}),`\n`,_jsx(Danger,{children:_jsx(_components.p,{children:`Do not connect alkaline or NiMH batteries to J6, and do not apply more than 4.2 V to the single-cell battery input. Reversed polarity can damage the board.`})}),`\n`,_jsx(Heading,{level:`3`,id:`regulated-logic-power`,children:`Regulated logic power`}),`\n`,_jsx(_components.p,{children:`The AP2112K-3.3 regulator supplies the board’s 3.3 V logic rail from +BATT. The regulator datasheet specifies a 600 mA continuous load rating; the available board-level current also depends on thermal conditions and other loads. The 3.3 V rail is exposed on J2 pins 2 and 3, pad J3, and Glink connector J5 pin 2.`}),`\n`,_jsx(_components.p,{children:`Do not power motors from a GPIO pin or the 3.3 V rail.`}),`\n`,_jsx(Heading,{level:`3`,id:`motor-power`,children:`Motor power`}),`\n`,_jsxs(_components.p,{children:[`The TB6612FNG logic `,_jsx(_components.strong,{children:`VCC`}),` pin is connected to the 3.3 V rail. Its motor `,_jsx(_components.strong,{children:`VM`}),` pins connect to the board’s `,_jsx(_components.strong,{children:`+BATT`}),` rail, which is also exposed at J1 pin 1. The schematic does not show a separate motor-supply connector; the motor driver’s supply follows the board’s USB/battery power path.`]}),`\n`,_jsxs(_components.p,{children:[`The TB6612FNG IC has a 2.5–13.5 V motor-supply operating range, with 1.2 A average output per channel. Its 3.2 A rating is for a single pulse and is not a continuous rating. These are IC limits; they do not mean the board’s battery input can accept 13.5 V. Keep the board supply within its single-cell battery and system-rail limits, and check each motor’s stall current. See `,_jsx(_components.a,{href:`https://toshiba.semicon-storage.com/info/datasheet_en_20141001.pdf?did=10660`,children:`Toshiba’s TB6612FNG datasheet`}),`.`]}),`\n`,_jsxs(_components.p,{children:[`The controller, driver, and motor supply share ground. J7 carries Motor A outputs (AO_2 on pin 1, AO_1 on pin 2); J8 carries Motor B outputs (BO_2 on pin 1, BO_1 on pin 2). See `,_jsx(_components.a,{href:`/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-pinouts`,children:`Pinouts`}),`.`]}),`\n`,_jsx(Warning,{children:_jsx(_components.p,{children:`Do not apply a separate high-voltage motor supply to +BATT, J6, or the motor output connectors. +BATT is shared with the board power path. Check motor stall current and polarity before use.`})}),`\n`,_jsx(Heading,{level:`3`,id:`measuring-battery-voltage`,children:`Measuring battery voltage`}),`\n`,_jsxs(_components.p,{children:[`The board schematic labels GPIO1 as `,_jsx(_components.strong,{children:`D1/BATT_MSR`}),`. This signal is available at J1 pin 10 for battery-voltage measurement. See the board-specific `,_jsx(_components.a,{href:`/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-pinouts`,children:`pinout`}),` before connecting other circuitry to it.`]}),`\n`,_jsx(Heading,{level:`3`,id:`driver-standby`,children:`Driver standby`}),`\n`,_jsxs(_components.p,{children:[`The TB6612FNG `,_jsx(_components.strong,{children:`STBY`}),` input is connected to GPIO42. Drive STBY low to put the motor driver in standby; drive it high to enable the output channels. Standby disables the driver outputs, but it does not disconnect the board’s battery or USB power.`]}),`\n`,_jsxs(_components.p,{children:[`For general ESP32-S3 sleep modes and USB/battery guidance, see `,_jsx(_components.a,{href:`/documentation/modules/glyph/glyph-esp32s3/glyph-esp32-s3-power-management`,children:`Glyph S3 Power Management`}),`. See the `,_jsx(_components.a,{href:`https://www.diodes.com/part/view/AP2112?BackID=9304`,children:`AP2112 product datasheet`}),` and `,_jsx(_components.a,{href:`https://www.microchip.com/content/dam/mchp/documents/APID/ProductDocuments/DataSheets/MCP73831-Family-Data-Sheet-DS20001984H.pdf`,children:`MCP73831 charger datasheet`}),` for IC details.`]})]})}function MDXContent(props={}){const{wrapper:MDXLayout}={..._provideComponents(),...props.components};return MDXLayout?_jsx(MDXLayout,{...props,children:_jsx(_createMdxContent,{...props})}):_createMdxContent(props)}return{default:MDXContent};function _missingMdxReference(id,component){throw new Error(`Expected `+(component?`component`:`object`)+\" `\"+id+\"` to be defined: you likely forgot to import, pass, or provide it.\")}","frontmatter":{},"scope":{"config":{},"pageMetadata":{"description":"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.","title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management"}}},"mdxSourceWithNoJs":null},"mdxExtracts":{"tableOfContents":[{"title":"Power Management for Glyph S3 Motor Driver","slug":"power-management-for-glyph-s3-motor-driver","depth":2,"children":[{"title":"Battery + USB power","slug":"battery-+-usb-power","depth":3,"children":[]},{"title":"Regulated logic power","slug":"regulated-logic-power","depth":3,"children":[]},{"title":"Motor power","slug":"motor-power","depth":3,"children":[]},{"title":"Measuring battery voltage","slug":"measuring-battery-voltage","depth":3,"children":[]},{"title":"Driver standby","slug":"driver-standby","depth":3,"children":[]}]}],"codeExamples":{}},"jsLinks":[],"subdomain":"pcbcupid-bae3761c","siteName":"PCB Cupid","title":"Power Management - PCB Cupid","navMaps":{"firstHrefInVersion":{},"firstHrefInLanguage":{}},"lastModified":"2026-11-20T14:14:34.626Z","originalFileLocation":"documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management.mdx"},"headHtml":"\u003cscript data-mint-head>(function(){var d=document.documentElement,p=null;if(!p){try{p=localStorage.getItem(\"isDarkMode\")}catch(e){}if(p==='true')p='dark';else if(p==='false')p='light';if(p!=='light'\u0026\u0026p!=='dark'\u0026\u0026p!=='system')p=\"system\"}var r=p==='system'?(matchMedia(\"(prefers-color-scheme: dark)\").matches?'dark':'light'):p;d.classList.remove(r==='dark'?'light':'dark');d.classList.add(r);d.setAttribute(\"data-theme-preference\",p)})();\u003c/script>\u003cmeta data-mint-head name=\"description\" content=\"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\">\u003cmeta data-mint-head name=\"application-name\" content=\"PCB Cupid\">\u003cmeta data-mint-head name=\"generator\" content=\"Mintlify\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/android-chrome-192x192.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"apple-touch-icon\" type=\"image/png\" sizes=\"180x180\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/apple-touch-icon.png\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/favicon-16x16.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/favicon-32x32.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/favicon.ico\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon-dark/android-chrome-192x192.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon-dark/favicon-16x16.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon-dark/favicon-32x32.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon-dark/favicon.ico\" media=\"(prefers-color-scheme: dark)\">\u003cmeta data-mint-head property=\"og:title\" content=\"Power Management - PCB Cupid\">\u003cmeta data-mint-head property=\"og:description\" content=\"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\">\u003cmeta data-mint-head property=\"og:site_name\" content=\"PCB Cupid\">\u003cmeta data-mint-head property=\"og:url\" content=\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management\">\u003cmeta data-mint-head property=\"og:type\" content=\"website\">\u003cmeta data-mint-head property=\"og:image\" content=\"https://pcbcupid-bae3761c.mintlify.site/_mintlify/api/og/v2?division=Glyph+S3+Motor+Driver\u0026amp;title=Power+Management\u0026amp;description=Glyph+S3+Motor+Driver+USB%2C+battery%2C+regulator%2C+and+TB6612FNG+motor-supply+details+from+the+board+design.\u0026amp;theme=2c7e3818cca0f9e7f4434aa9\u0026amp;signature=db1cd6551077e215ed554ad4e9f0ef5d4118a9c3185b18c0803f15aaa9477610\">\u003cmeta data-mint-head property=\"og:image:width\" content=\"1200\">\u003cmeta data-mint-head property=\"og:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"twitter:card\" content=\"summary_large_image\">\u003cmeta data-mint-head name=\"twitter:title\" content=\"Power Management - PCB Cupid\">\u003cmeta data-mint-head name=\"twitter:description\" content=\"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\">\u003cmeta data-mint-head name=\"twitter:image\" content=\"https://pcbcupid-bae3761c.mintlify.site/_mintlify/api/og/v2?division=Glyph+S3+Motor+Driver\u0026amp;title=Power+Management\u0026amp;description=Glyph+S3+Motor+Driver+USB%2C+battery%2C+regulator%2C+and+TB6612FNG+motor-supply+details+from+the+board+design.\u0026amp;theme=2c7e3818cca0f9e7f4434aa9\u0026amp;signature=db1cd6551077e215ed554ad4e9f0ef5d4118a9c3185b18c0803f15aaa9477610\">\u003cmeta data-mint-head name=\"twitter:image:width\" content=\"1200\">\u003cmeta data-mint-head name=\"twitter:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"msapplication-config\" content=\"/mintlify-assets/_mintlify/favicons/pcbcupid-bae3761c/TFd0Eu1csuxrLpjH/_generated/favicon/browserconfig.xml\">\u003cmeta data-mint-head name=\"apple-mobile-web-app-title\" content=\"PCB Cupid\">\u003cmeta data-mint-head name=\"msapplication-TileColor\" content=\"#0D9373\">\u003clink data-mint-head rel=\"canonical\" href=\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management\">\u003clink data-mint-head rel=\"alternate\" type=\"application/xml\" href=\"/sitemap.xml\">\u003clink data-mint-head rel=\"alternate\" type=\"text/markdown\" href=\"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management.md\">\u003cscript data-mint-head type=\"application/ld+json\">{\"@context\":\"https://schema.org\",\"@graph\":[{\"@type\":\"Organization\",\"@id\":\"https://learn.pcbcupid.com/#organization\",\"name\":\"PCB Cupid\",\"url\":\"https://learn.pcbcupid.com\"},{\"@type\":\"WebSite\",\"@id\":\"https://learn.pcbcupid.com#website\",\"name\":\"PCB Cupid\",\"url\":\"https://learn.pcbcupid.com\",\"publisher\":{\"@id\":\"https://learn.pcbcupid.com/#organization\"}},{\"@type\":\"WebPage\",\"@id\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management#webpage\",\"url\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management\",\"name\":\"Power Management\",\"description\":\"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\",\"dateModified\":\"2026-11-20T14:14:34.626Z\",\"isPartOf\":{\"@id\":\"https://learn.pcbcupid.com#website\"},\"breadcrumb\":{\"@id\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management#breadcrumb\"}},{\"@type\":\"BreadcrumbList\",\"@id\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Modules\",\"item\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32c3/overview-glyph-c3\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Glyph\",\"item\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32c3/overview-glyph-c3\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Glyph S3 Motor Driver\",\"item\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver\"},{\"@type\":\"ListItem\",\"position\":4,\"name\":\"Power Management\",\"item\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management\"}]},{\"@type\":[\"Article\",\"TechArticle\"],\"@id\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management#article\",\"headline\":\"Power Management\",\"name\":\"Power Management\",\"description\":\"Glyph S3 Motor Driver USB, battery, regulator, and TB6612FNG motor-supply details from the board design.\",\"url\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management\",\"mainEntityOfPage\":{\"@id\":\"https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management#webpage\"},\"dateModified\":\"2026-11-20T14:14:34.626Z\",\"publisher\":{\"@id\":\"https://learn.pcbcupid.com/#organization\"},\"isPartOf\":{\"@id\":\"https://learn.pcbcupid.com#website\"}}]}\u003c/script>\u003cscript data-mint-head type=\"application/ld+json\">{\"@context\":\"https://schema.org\",\"@type\":\"WebSite\",\"name\":\"PCB Cupid\",\"publisher\":{\"@type\":\"Organization\",\"name\":\"PCB Cupid\"},\"provider\":{\"@type\":\"Organization\",\"name\":\"Mintlify\",\"url\":\"https://mintlify.com\"}}\u003c/script>","agentPointerHref":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management.md","siteName":"PCB Cupid","nav":{"global":null,"tabs":[{"tab":"Documentation","groups":[{"group":"Welcome","pages":[{"title":"Introduction","href":""},{"title":"Getting Started","href":"/documentation/welcome/getting-started"},{"group":"Prerequisites","pages":[{"title":"Setting Up MCP","href":"/documentation/welcome/prerequisites/setting-up-mcp"},{"title":"Arduino IDE Setup","href":"/documentation/welcome/prerequisites/arduino-ide-setup"},{"title":"ESP-IDF Setup for Glyph Boards","href":"/documentation/welcome/prerequisites/esp-idf"},{"title":"Smowcode IDE Setup","href":"/documentation/welcome/prerequisites/smowcode-ide-setup"},{"title":"Code Composer Studio IDE Setup","href":"/documentation/welcome/prerequisites/cc-studio"},{"title":"Glink Connector Overview","href":"/documentation/welcome/prerequisites/glink"},{"title":"CircuitPython Setup Guide","href":"/documentation/welcome/prerequisites/circuitpython-setup-guide"}]}]},{"group":"Modules","pages":[{"group":"Glyph","pages":[{"group":"Glyph C3","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-esp32c3/overview-glyph-c3"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-esp32c3/pinouts"},{"title":"Assembly","sidebarTitle":"Assembly","href":"/documentation/modules/glyph/glyph-esp32c3/assembly"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32c3/power-management"}]},{"group":"Glyph C6","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-esp32c6/overview-glyph-c6"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-esp32c6/glyphc6-pinouts"},{"title":"Assembly","sidebarTitle":"Assembly","href":"/documentation/modules/glyph/glyph-esp32c6/glyphc6-assembly"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32c6/glyph-esp32-c6-power-management"}]},{"group":"Glyph H2","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-esp32h2/overview-glyph-h2"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-esp32h2/pinouts-h2"},{"title":"Assembly","sidebarTitle":"Assembly","href":"/documentation/modules/glyph/glyph-esp32h2/glyph-assembly"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32h2/power-management-glyph"}]},{"group":"Glyph S3","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-overview"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-esp32-s3-pinouts"},{"title":"Assembly","sidebarTitle":"Assembly","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-esp32-s3-assembly"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-esp32-s3-power-management"}]},{"group":"Glyph S3 Lucid","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-s3-lucid/overview"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-s3-lucid/pinouts"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-s3-lucid/power-management"}]},{"group":"Glyph S3 Motor Driver","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver"},{"description":"Glyph S3 Motor Driver pinout reference for its ESP32-S3 headers, solder pads, motor outputs, USB-C, battery, and Glink connectors.","title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-pinouts"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management"}]},{"group":"Glyph C5","pages":[{"description":"Overview of the Glyph C5 development board: a compact RISC-V microcontroller with dual-band Wi-Fi 6, Bluetooth LE, 802.15.4, and Qwiic-compatible Glink connector.","title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-c5/overview-glyph-c5"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-c5/pinouts"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-c5/power-management"}]},{"group":"Glyph 2040","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph/glyph-2040/overview-glyph-2040"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph/glyph-2040/pinouts"},{"title":"Power Management","sidebarTitle":"Power Management","href":"/documentation/modules/glyph/glyph-2040/power-management"}]}]},{"group":"Glyph Mini","pages":[{"group":"Glyph Mini 2040","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/glyph-mini/glyph-mini-2040/overview"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/glyph-mini/glyph-mini-2040/pinouts"}]}]},{"group":"TERRA","pages":[{"group":"EC200U","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/terra/terralink-ec200u/overview"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/terra/terralink-ec200u/pinouts"},{"title":"Programming with Glyph","sidebarTitle":"Programming","href":"/documentation/modules/terra/terralink-ec200u/programming"}]},{"group":"A7672S","pages":[{"title":"Overview","sidebarTitle":"Overview","href":"/documentation/modules/terra/terralink-a7672s/overview"},{"title":"Pinouts","sidebarTitle":"Pinouts","href":"/documentation/modules/terra/terralink-a7672s/pinouts"},{"title":"Programming with Glyph","sidebarTitle":"Programming","href":"/documentation/modules/terra/terralink-a7672s/programming"}]}]},{"group":"G-Mod","pages":[{"title":"1-Channel Relay","sidebarTitle":"1-Channel Relay","href":"/documentation/modules/g-mod/1-ch-relay"},{"title":"2-Channel Relay","sidebarTitle":"2-Channel Relay","href":"/documentation/modules/g-mod/relay"},{"title":"Micro SD Card","sidebarTitle":"SD Card","href":"/documentation/modules/g-mod/sd-card"},{"title":"MCP79412 RTC","sidebarTitle":"MCP79412 RTC","href":"/documentation/modules/g-mod/mcp79412-rtc"},{"title":"PCF8563 Real-Time Clock Module","sidebarTitle":"PCF8563 RTC","href":"/documentation/modules/g-mod/pcf8563-rtc"},{"title":"Limit Switch Module","sidebarTitle":"Limit Switch","href":"/documentation/modules/g-mod/limit-switch"},{"title":"WS2812B RGB Ring","sidebarTitle":"WS2812B RGB Ring","href":"/documentation/modules/g-mod/ws2812b-led"},{"title":"Key Array","sidebarTitle":"Key Array","href":"/documentation/modules/g-mod/key-array"},{"title":"Serial Flash","sidebarTitle":"Serial Flash","href":"/documentation/modules/g-mod/serial-flash"},{"title":"Dual Motor Driver","sidebarTitle":"Motor Driver","href":"/documentation/modules/g-mod/motor-driver"},{"title":"Lithium Charger","sidebarTitle":"Lithium Charger","href":"/documentation/modules/g-mod/lithium-charger"},{"title":"DC-DC Buck Converter (SY81103)","sidebarTitle":"Buck Converter","href":"/documentation/modules/g-mod/dc-buck-converter"},{"title":"DC-DC Boost Converter (SX1308)","sidebarTitle":"Boost Converter","href":"/documentation/modules/g-mod/dc-boost-converter"},{"title":"Audio Codec","sidebarTitle":"Audio Codec","href":"/documentation/modules/g-mod/audio-codec"},{"title":"CAN Bus Transceiver","sidebarTitle":"CAN Bus","href":"/documentation/modules/g-mod/can-bus"},{"title":"RS-485 Transceiver","sidebarTitle":"RS-485 Transceiver","href":"/documentation/modules/g-mod/rs-485-transceiver"},{"title":"Bi-Directional Voltage-Level Translator","sidebarTitle":"Voltage-Level Translator","href":"/documentation/modules/g-mod/bi-voltage-level-translator"}]},{"group":"G-Sense","pages":[{"title":"Single-Channel I2S Microphone","sidebarTitle":"Microphone","href":"/documentation/modules/g-sense/microphone"},{"title":"Single-Channel I2S Microphone (T5848)","sidebarTitle":"Microphone (T5848)","href":"/documentation/modules/g-sense/t5848-microphone"},{"title":"2-Channel Microphone","sidebarTitle":"2-Channel Microphone","href":"/documentation/modules/g-sense/2-channel-microphone"},{"title":"SHT35 Temperature and Humidity Sensor","sidebarTitle":"SHT35","href":"/documentation/modules/g-sense/sht35"},{"title":"SHT45 Temperature and Humidity Sensor","sidebarTitle":"SHT45","href":"/documentation/modules/g-sense/sht45"},{"title":"GSI003 Industrial Temp \u0026 Humidity Sensor","sidebarTitle":"GSI003","href":"/documentation/modules/g-sense/hdc3020-rs485"},{"title":"QMC6309 Magnetometer","sidebarTitle":"QMC6309 Magnetometer","href":"/documentation/modules/g-sense/qmc6309-magnetometer"},{"title":"Capacitive Touch Slider","sidebarTitle":"Capacitive Touch Slider","href":"/documentation/modules/g-sense/capacitive-touch-slider"}]},{"group":"G-Kit","pages":[{"title":"SoundBox — DIY MP3 Player","sidebarTitle":"MP3 Player","href":"/documentation/modules/g-kit/soundbox"}]},{"group":"Breakout Boards","pages":[{"title":"Qwiic 2-in-1","sidebarTitle":"Qwiic 2-in-1","href":"/documentation/modules/breakout-boards/qwiic-2-in-1"},{"title":"Qwiic 4-in-1","sidebarTitle":"Qwiic 4-in-1","href":"/documentation/modules/breakout-boards/qwiic-4-in-1"},{"title":"USB 4-in-1","sidebarTitle":"USB 4-in-1","href":"/documentation/modules/breakout-boards/usb-4-in-1"},{"title":"USB-A Female","sidebarTitle":"USB-A Female","href":"/documentation/modules/breakout-boards/usb-a-breakout-female"},{"title":"USB-A Male","sidebarTitle":"USB-A Male","href":"/documentation/modules/breakout-boards/usb-a-breakout-male"},{"title":"USB-C","sidebarTitle":"USB-C","href":"/documentation/modules/breakout-boards/usb-c"}]},{"group":"Gadgets","pages":[{"title":"USB to RS485 Converter","sidebarTitle":"USB to RS485","href":"/documentation/modules/gadgets/usb-to-rs485"},{"title":"USB to TTL Converter","sidebarTitle":"USB to TTL","href":"/documentation/modules/gadgets/usb-ttl"}]}]},{"group":"Enclosure","pages":[{"title":"3D Printed Enclosure for Glyph C3/C6","sidebarTitle":"Enclosure-C3/C6","href":"/documentation/enclosure/3d-printed-enclosure-for-glyph-esp32-boards"}]}]},{"tab":"Examples","pages":[{"title":"Examples","href":"/guides/arduino-ide-blink-led"}]},{"tab":"PCB Design","pages":[{"title":"PCB Design","href":"/pcb-design/design/kicad/introduction-on-kicad"}]}]},"basePath":"","title":"Power Management - PCB Cupid","deploymentId":"dpl_2pTxFtyBudBMYZiCw1MyvoA1wxpd","buildId":"dpl_2pTxFtyBudBMYZiCw1MyvoA1wxpd","dynamics":[],"chunks":[]}