Skip to main content
The GLYPH S3 Motor Driver combines an ESP32-S3 development board with an onboard TB6612FNG dual H-bridge motor driver. It controls two brushed DC motors independently, or one bipolar stepper motor, while the S3 handles application logic, sensing, and wireless connectivity.
Controller
  • Module: ESP32-S3-MINI-1-N8
  • Flash: 8 MB Quad SPI
  • PSRAM: None
Motor Driver
  • IC: Toshiba TB6612FNG
  • Outputs: Two DC motor channels
  • Control: Direction and PWM speed control
The board measures approximately 50.9 mm × 22.9 mm × 1.6 mm from the PCB design, without headers soldered. It uses the ESP32-S3-MINI-1-N8 configuration: 8 MB Quad SPI flash and no PSRAM. The ESP32-S3 has a dual-core Xtensa LX7 processor, up to 240 MHz, and 512 KB internal SRAM. See the Espressif module datasheet.
  • Logic voltage: 3.3 V
  • GPIO and buses: GPIO, ADC, I²C, SPI, UART, PWM, and native USB functions; some GPIOs are used internally by the motor driver
  • USB-C: Board power, native USB programming, and serial debugging
  • Battery: Single-cell LiPo/Li-ion connector with an onboard MCP73831 charger and USB/battery power path
  • 3.3 V regulator: AP2112K-3.3, rated for up to 600 mA continuous load by the regulator datasheet
  • Motor outputs: Two integrated TB6612FNG output channels on dedicated motor connectors
  • Glink: Qwiic/STEMMA QT-compatible I²C connector
  • Onboard controls: BOOT and RESET buttons; onboard LED on GPIO21
  • Battery measurement: GPIO1 is also assigned to BATT_MSR
The USB VBUS and battery path feed the board’s +BATT rail. The motor driver’s VM supply is connected to this same rail. See Power Management before choosing a motor supply.

Integrated dual motor control

The onboard TB6612FNG provides two direction-and-speed control channels. It supports two brushed DC motors or one bipolar stepper motor, with braking, coast, and standby modes. Integrating the driver removes the need to stack a separate motor-driver module onto the controller.
  • Motor supply range: 2.5–13.5 V
  • Output current: 1.2 A average per channel; 3.2 A single-pulse peak per the IC datasheet
  • Control: Direction inputs and PWM speed control
The peak rating is for a single pulse, not continuous operation. Usable current depends on the motor, PCB cooling, and operating conditions. See Toshiba’s TB6612FNG datasheet.
Select a motor supply that matches the motors and stays within the TB6612FNG limits. Check motor stall current and wiring polarity before powering the board. Do not treat the single-pulse peak rating as continuous current.

Native Bootloader and Programming

The Glyph S3 Motor Driver uses the ESP32-S3 native USB bootloader. Hold BOOT while connecting the USB-C cable to enter download mode, then select the detected serial port in the development environment. USB-C also provides serial debugging.

Connectivity

The ESP32-S3-MINI-1 module provides 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth LE. This allows the board to receive motion commands and report sensor or motor-control data wirelessly.
The wireless module on the GLYPH board is CE and FCC certified.

Development Support

The Glyph S3 Motor Driver can be programmed with:
  • Arduino
  • MicroPython
  • ESP-IDF (Espressif IoT Development Framework)

Memory and Storage

This board uses the N8 module version with 8 MB Quad SPI flash and no external PSRAM. It also has 512 KB internal SRAM for the ESP32-S3’s runtime and buffers.

S3 Chip Features

  • BluFi
  • RF coexistence
  • ESP-BLE-MESH
  • ESP-WIFI-MESH
For more ESP32-S3 details, see the ESP32-S3 datasheet and Espressif’s getting-started guide.

Project uses

The integrated controller and driver make this a compact premium option for two-wheel robots, differential-drive vehicles, pan-and-tilt mechanisms, and other builds that combine wireless control with motion. The motor driver handles the motor outputs while the ESP32-S3 remains available for project code and connected peripherals. For the board-specific connections, see Pinouts and Power Management.