> ## Documentation Index
> Fetch the complete documentation index at: https://learn.pcbcupid.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Overview

> Overview of the Glyph S3 Motor Driver, an ESP32-S3 board with an integrated dual motor driver.

[Shop now](https://shop.pcbcupid.com/product/gd011/)

3D VIEW

<dialog>×</dialog>

The **GLYPH S3 Motor Driver** combines an ESP32-S3 development board with an onboard **TB6612FNG dual H-bridge motor driver**. It controls two brushed DC motors independently, or one bipolar stepper motor, while the S3 handles application logic, sensing, and wireless connectivity.

Controller

<ul>
  <li>**Module:** ESP32-S3-MINI-1-N8</li>
  <li>**Flash:** 8 MB Quad SPI</li>
  <li>**PSRAM:** None</li>
</ul>

Motor Driver

<ul>
  <li>**IC:** Toshiba TB6612FNG</li>
  <li>**Outputs:** Two DC motor channels</li>
  <li>**Control:** Direction and PWM speed control</li>
</ul>

The board measures approximately **50.9 mm × 22.9 mm × 1.6 mm** from the PCB design, without headers soldered. It uses the **ESP32-S3-MINI-1-N8** configuration: 8 MB Quad SPI flash and no PSRAM. The ESP32-S3 has a dual-core Xtensa LX7 processor, up to 240 MHz, and 512 KB internal SRAM. See the [Espressif module datasheet](https://documentation.espressif.com/esp32-s3-mini-1_mini-1u_datasheet_en.html).

* **Logic voltage:** 3.3 V
* **GPIO and buses:** GPIO, ADC, I²C, SPI, UART, PWM, and native USB functions; some GPIOs are used internally by the motor driver
* **USB-C:** Board power, native USB programming, and serial debugging
* **Battery:** Single-cell LiPo/Li-ion connector with an onboard MCP73831 charger and USB/battery power path
* **3.3 V regulator:** AP2112K-3.3, rated for up to 600 mA continuous load by the regulator datasheet
* **Motor outputs:** Two integrated TB6612FNG output channels on dedicated motor connectors
* **Glink:** Qwiic/STEMMA QT-compatible I²C connector
* **Onboard controls:** BOOT and RESET buttons; onboard LED on GPIO21
* **Battery measurement:** GPIO1 is also assigned to BATT\_MSR

The USB VBUS and battery path feed the board's **+BATT** rail. The motor driver's VM supply is connected to this same rail. See [Power Management](https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management.md) before choosing a motor supply.

## Integrated dual motor control

The onboard TB6612FNG provides two direction-and-speed control channels. It supports two brushed DC motors or one bipolar stepper motor, with braking, coast, and standby modes. Integrating the driver removes the need to stack a separate motor-driver module onto the controller.

* **Motor supply range:** 2.5–13.5 V
* **Output current:** 1.2 A average per channel; 3.2 A single-pulse peak per the IC datasheet
* **Control:** Direction inputs and PWM speed control

The peak rating is for a single pulse, not continuous operation. Usable current depends on the motor, PCB cooling, and operating conditions. See [Toshiba's TB6612FNG datasheet](https://toshiba.semicon-storage.com/info/datasheet_en_20141001.pdf?did=10660).

> [!WARNING]
>
> Select a motor supply that matches the motors and stays within the TB6612FNG limits. Check motor stall current and wiring polarity before powering the board. Do not treat the single-pulse peak rating as continuous current.

### Native Bootloader and Programming

The Glyph S3 Motor Driver uses the ESP32-S3 native USB bootloader. Hold **BOOT** while connecting the USB-C cable to enter download mode, then select the detected serial port in the development environment. USB-C also provides serial debugging.

### Connectivity

The ESP32-S3-MINI-1 module provides 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth LE. This allows the board to receive motion commands and report sensor or motor-control data wirelessly.

> [!NOTE]
>
> The wireless module on the GLYPH board is CE and FCC certified.

### Development Support

The Glyph S3 Motor Driver can be programmed with:

* **Arduino**
* **MicroPython**
* **ESP-IDF (Espressif IoT Development Framework)**

### Memory and Storage

This board uses the **N8** module version with **8 MB Quad SPI flash** and **no external PSRAM**. It also has 512 KB internal SRAM for the ESP32-S3's runtime and buffers.

### S3 Chip Features

* **BluFi**
* **RF coexistence**
* **ESP-BLE-MESH**
* **ESP-WIFI-MESH**

For more ESP32-S3 details, see the [ESP32-S3 datasheet](https://files.pcbcupid.com/Documentation/Boards/glyph-S3/PCBCUPID_esp32-s3_datasheet.pdf) and [Espressif's getting-started guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32s3/get-started/).

## Project uses

The integrated controller and driver make this a compact premium option for two-wheel robots, differential-drive vehicles, pan-and-tilt mechanisms, and other builds that combine wireless control with motion. The motor driver handles the motor outputs while the ESP32-S3 remains available for project code and connected peripherals.

For the board-specific connections, see [Pinouts](https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-pinouts.md) and [Power Management](https://learn.pcbcupid.com/documentation/modules/glyph/glyph-esp32s3/glyph-s3-motor-driver-power-management.md).


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.